Log in Sign up

Cart (0) Check Out

FLIGHT CONTROLLER F722-SE

Regular price $53.99

MANUAL (15M)

FC Specifications

MCU: 216MHz STM32F722RET6
IMU: MPU6000 & ICM20602, Dual Gyros built-in (SPI)
Baro: BMP280 or DPS310(I2C)
OSD: AT7456E (SPI)
Blackbox: MicroSD card slot (SPI)
5x Uarts (1,2,3,4,6) with build-in inversion
1x Softserial supported
8x Dshot/Proshot/oneshot outputs
1x I2C
4x RX6 pad(one per cornet) for BLheli32 ESC telemetry
4x individual ESC power/signal pads
1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
Vbat filtered output power for VTX, Switchable via AUX (modes tab-user1)
Dual Camera image switchable via AUX (modes tab-user2)

Camera control: Yes
Smartaudio & Tramp VTX protocol: Yes
WS2812 Led Strip : Yes
Beeper : Yes
RSSI: Yes
Additional ADC for INAV analog airspeed

PDB Specifications

Input: 6~36V (3~8S LiPo) w/TVS protection
PDB: 4x35A (Max.4x46A)
BEC: 5V 2A cont. (Max.3A)
LDO 3.3V: Max.200mA
Current Sensor 184A (Scale 179)
Battery Voltage Sensor: 1:10 (Scale 110)

FC Firmware

BetaFlight / INAV
Target: MATEKF722SE

Physical

Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
Dimensions: 36 x 46 mm
Weight: 10g

Including

1x FC F722-SE
6x silicon grommets M4 to M3
1x FR4 PCB Plate 36*36*1mm
1x Rubycon ZLH 35V/470uF (Low ESR)

Pad Hole	Pin name	Function	BetaFlight	BetaFlight	INav	INav	INav	INav	INav
Pad Hole	Pin name	Function	Octo	Quad	Tricopter	Quad X	Hex X	Flying Wing	Airplane
S1	PB4	TIM3_CH1	motor-1	motor-1	motor-1	motor-1	motor-1	servo	servo
S2	PB5	TIM3_CH2	motor-2	motor-2	motor-2	motor-2	motor-2	servo	servo
S3	PB0	TIM3_CH3	motor-3	motor-3	motor-3	motor-3	motor-3		servo
S4	PB1	TIM3_CH4	motor-4	motor-4		motor-4	motor-4		servo
S5	PA15	TIM2_CH1	motor-5				motor-5		servo
S6	PB3	TIM2_CH2	motor-6				motor-6		servo
S7	PB6	TIM4_CH1	motor-7		servo	servo	servo	motor-1	motor-1
S8	PB7	TIM4_CH2	motor-8			servo	servo	motor-2	motor-2

LED	PA8	TIM1_CH1	2812LED	2812LED	2812LED	2812LED	2812LED	2812LED	2812LED
RX2	PA3	TIM9_CH2	RX2/ppm	RX2/ppm	RX2/ppm	RX2/ppm	RX2/ppm	RX2/ppm	RX2/ppm
TX2	PA2	TIM9_CH1	TX2/pwm1	TX2/pwm1
RX4	PA1	TIM5_CH2	RX2/pwm2 Cam_Ctrl	RX2/pwm2 Cam_Ctrl
TX4	PA0	TIM5_CH1	TX4/pwm3	TX4/pwm3

PA4	PA4	ADC	/	/				AirSpeed	AirSpeed

- F722-SE DPS310 ver. and previous BMP280 version have same layout and components except for barometer & battery pads style.
- INAV2.5.x and Betaflight 4.2.x downloaded from configurator don’t support new barometer DPS310.
- DPS310 has been supported officially by INAV2.6/ BetaFlight 4.3 and new configurator.
- For now, pls download customized INAV2.5.x and BetaFlight 4.2.x below.
inav_2.5.1_MATEKF722SE_DPS310.hex

If Baro can’t be detected automatically. In INAV CLI mode, type command
- set baro_hardware = DPS310
- save
betaflight_4.2.3_MATEKF722SE_DPS310.hex

betaflight_4.2.8_MATEKF722SE.hex

If Baro can’t be detected automatically. In BF CLI mode, type command
- set baro_bustype = I2C
- set baro_i2c_device = 1
- set baro_i2c_address = 118
- set baro_hardware = DPS310
- save